You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
72 lines
3.3 KiB
Plaintext
72 lines
3.3 KiB
Plaintext
# Install the required tools and dependencies
|
|
sudo apt-get update
|
|
sudo apt-get install git cmake build-essential libqt4-dev libusb-1.0-0-dev python-dev libxrender-dev python
|
|
|
|
# OSMC dependencies
|
|
sudo apt-get install rbp-userland-dev-osmc
|
|
|
|
# Arch/ALARM dependencies
|
|
sudo pacman -S --needed git cmake base-devel qt4 libusb libxrender icu
|
|
|
|
# RPI ONLY: when you build on the raspberry pi and include the dispmanx grabber (which is the default)
|
|
# you also need the firmware including headers installed. This downloads the firmware from the raspberrypi github
|
|
# and copies the required files to the correct place. The firmware directory can be deleted afterwards if desired.
|
|
export FIRMWARE_DIR="raspberrypi-firmware"
|
|
git clone --depth 1 https://github.com/raspberrypi/firmware.git "$FIRMWARE_DIR"
|
|
sudo cp -R "$FIRMWARE_DIR/hardfp/opt/" /opt
|
|
|
|
# OpenCV HDMI grabber dependencies (must be version 2.x) (check with: pkg-config --modversion opencv)
|
|
sudo apt-get install libopencv*
|
|
|
|
# create hyperion directory and checkout the code from github
|
|
# You might want to add "--depth 1" if you only want to recompile the current source or don't want to use git any further
|
|
export HYPERION_DIR="hyperion"
|
|
git clone --recursive https://github.com/tvdzwan/hyperion.git "$HYPERION_DIR"
|
|
|
|
# if you forget the --recursive in above statement or you are updating an existing clone you need
|
|
# to clone the protobuf submodule by running the following two statements:
|
|
git submodule init
|
|
git submodule update
|
|
|
|
# create and enter the build directory
|
|
mkdir "$HYPERION_DIR/build"
|
|
cd "$HYPERION_DIR/build"
|
|
|
|
# run cmake to generate make files on the raspberry pi WITHOUT PWM SUPPORT
|
|
cmake -DCMAKE_BUILD_TYPE=Release -DPLATFORM="rpi" -Wno-dev ..
|
|
# run cmake to generate make files on the raspberry pi WITH PWM SUPPORT
|
|
cmake -DCMAKE_BUILD_TYPE=Release -DPLATFORM="rpi-pwm" -Wno-dev ..
|
|
# or if you are not compiling on the raspberry pi (e.g. OrangePi) and need to disable the Dispmanx grabber and support for spi devices
|
|
cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_X11=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev ..
|
|
# to enable the HDMI OpenCV grabber append cmake parameter
|
|
ENABLE_OPENCV=ON
|
|
# on amlogic platforms
|
|
cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_AMLOGIC=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev ..
|
|
# as an alternative for the dispmanx grabber on non-rpi devices (e.g. cubox-i) you could try the framebuffer grabber
|
|
cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_FB=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev ..
|
|
# for OSX build you need XCode, qt4 libraries and cmake (maybe libusb too). You can use macport or homebrew(recommended) to install them:
|
|
#for port:
|
|
sudo port install qt4-mac
|
|
sudo port install cmake
|
|
#sudo port install libusb
|
|
#for brew:
|
|
sudo brew tap cartr/qt4
|
|
sudo brew tap-pin cartr/qt4
|
|
sudo brew install qt@4
|
|
sudo brew install cmake
|
|
#sudo brew install libusb
|
|
cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_V4L2=OFF -DENABLE_OSX=ON ..
|
|
|
|
# run make to build Hyperion
|
|
make -j $(nproc)
|
|
|
|
#after compile, to remove any stuff not needed for a release version.
|
|
strip bin/*
|
|
|
|
# The binaries are built in "$HYPERION_DIR/build/bin". You could copy those to /usr/bin
|
|
sudo cp ./bin/hyperion-remote /usr/bin/
|
|
sudo cp ./bin/hyperiond /usr/bin/
|
|
|
|
# Copy the effect folder (if you did not use the normal installation method before)
|
|
sudo mkdir -p /opt/hyperion/effects && sudo cp -R ../effects/ /opt/hyperion/
|