# Install the required tools and dependencies sudo apt-get update sudo apt-get install git cmake build-essential libqt4-dev libusb-1.0-0-dev python-dev libxrender-dev python # OSMC dependencies sudo apt-get install rbp-userland-dev-osmc # Arch/ALARM dependencies sudo pacman -S --needed git cmake base-devel qt4 libusb libxrender icu # RPI ONLY: when you build on the raspberry pi and include the dispmanx grabber (which is the default) # you also need the firmware including headers installed. This downloads the firmware from the raspberrypi github # and copies the required files to the correct place. The firmware directory can be deleted afterwards if desired. export FIRMWARE_DIR="raspberrypi-firmware" git clone --depth 1 https://github.com/raspberrypi/firmware.git "$FIRMWARE_DIR" sudo cp -R "$FIRMWARE_DIR/hardfp/opt/" /opt # OpenCV HDMI grabber dependencies (must be version 2.x) (check with: pkg-config --modversion opencv) sudo apt-get install libopencv* # create hyperion directory and checkout the code from github # You might want to add "--depth 1" if you only want to recompile the current source or don't want to use git any further export HYPERION_DIR="hyperion" git clone --recursive https://github.com/tvdzwan/hyperion.git "$HYPERION_DIR" # if you forget the --recursive in above statement or you are updating an existing clone you need # to clone the protobuf submodule by running the following two statements: git submodule init git submodule update # create and enter the build directory mkdir "$HYPERION_DIR/build" cd "$HYPERION_DIR/build" # run cmake to generate make files on the raspberry pi WITHOUT PWM SUPPORT cmake -DCMAKE_BUILD_TYPE=Release -DPLATFORM="rpi" -Wno-dev .. # run cmake to generate make files on the raspberry pi WITH PWM SUPPORT cmake -DCMAKE_BUILD_TYPE=Release -DPLATFORM="rpi-pwm" -Wno-dev .. # or if you are not compiling on the raspberry pi (e.g. OrangePi) and need to disable the Dispmanx grabber and support for spi devices cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_X11=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev .. # to enable the HDMI OpenCV grabber append cmake parameter ENABLE_OPENCV=ON # on amlogic platforms cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_AMLOGIC=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev .. # as an alternative for the dispmanx grabber on non-rpi devices (e.g. cubox-i) you could try the framebuffer grabber cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_FB=ON -DCMAKE_BUILD_TYPE=Release -Wno-dev .. # for OSX build you need XCode, qt4 libraries and cmake (maybe libusb too). You can use macport or homebrew(recommended) to install them: #for port: sudo port install qt4-mac sudo port install cmake #sudo port install libusb #for brew: sudo brew tap cartr/qt4 sudo brew tap-pin cartr/qt4 sudo brew install qt@4 sudo brew install cmake #sudo brew install libusb cmake -DENABLE_DISPMANX=OFF -DENABLE_SPIDEV=OFF -DENABLE_V4L2=OFF -DENABLE_OSX=ON .. # run make to build Hyperion make -j $(nproc) #after compile, to remove any stuff not needed for a release version. strip bin/* # The binaries are built in "$HYPERION_DIR/build/bin". You could copy those to /usr/bin sudo cp ./bin/hyperion-remote /usr/bin/ sudo cp ./bin/hyperiond /usr/bin/ # Copy the effect folder (if you did not use the normal installation method before) sudo mkdir -p /opt/hyperion/effects && sudo cp -R ../effects/ /opt/hyperion/