CompileOnOrangepi Document added
How to compile on Orange pi is added.
This commit is contained in:
parent
7d5fe512d1
commit
c7f5402db8
|
@ -0,0 +1,88 @@
|
|||
# Install on Armbian Orange Pi Zero
|
||||
>Tested on Armbian_19.11.3_Orangepizero_bionic_current_5.3.9
|
||||
|
||||
Following Steps can be used to build and install on Arbian on Orange Pi
|
||||
1. First update and upgrade Arbian and make sure you are connected to Internet
|
||||
```sh
|
||||
$ sudo apt update & apt upgrade
|
||||
```
|
||||
>You may reboot after this
|
||||
2. Install the necessary softwares required for build
|
||||
```sh
|
||||
$ sudo apt-get install git cmake build-essential libqt4-dev libusb-1.0-0-dev python-dev libxrender-dev python
|
||||
```
|
||||
3. Download and build the hyperion using the following command
|
||||
```sh
|
||||
$ export HYPERION_DIR="hyperion"
|
||||
$ git clone --recursive https://github.com/tvdzwan/hyperion.git "$HYPERION_DIR"
|
||||
$ mkdir "$HYPERION_DIR/build"
|
||||
$ cd "$HYPERION_DIR/build"
|
||||
$ cmake -DENABLE_DISPMANX=OFF -DENABLE_OPENCV=OFF -DENABLE_SPIDEV=ON -DENABLE_X11=OFF -DCMAKE_BUILD_TYPE=Release -Wno-dev ..
|
||||
$ make -j $(nproc)
|
||||
$ strip bin/*
|
||||
```
|
||||
4. Install manually hyperion using the following command
|
||||
```sh
|
||||
$ sudo cp ./bin/hyperion-remote /usr/bin/
|
||||
$ sudo cp ./bin/hyperiond /usr/bin/
|
||||
$ sudo cp ./bin/hyperion-v4l2 /usr/bin/
|
||||
```
|
||||
5. Copy the effects and configurations
|
||||
```sh
|
||||
$ sudo mkdir -p /usr/share/hyperion/effects && sudo cp -R ../effects/ /usr/share/hyperion/
|
||||
$ sudo mkdir -p /etc/hyperion
|
||||
```
|
||||
6. Copy Startup scripts
|
||||
```sh
|
||||
$ sudo mkdir -p /etc/init/ && sudo cp ../bin/service/hyperion.initctl.sh /etc/init/hyperion.conf
|
||||
$ sudo cp ../bin/service/hyperion.init.sh /etc/init.d/hyperion
|
||||
$ sudo cp ../bin/service/hyperion.systemd.sh /etc/systemd/system/hyperion.service
|
||||
```
|
||||
7. In case Hypercon is not able to copy automatically, manually copy the copy hyperion.config.json to /etc/hyperion folder
|
||||
8. Finally to make hyperion auto start during boot up, execute following commands
|
||||
```sh
|
||||
$ sudo systemctl enable hyperion
|
||||
$ sudo systemctl start hyperion
|
||||
```
|
||||
> Extras,
|
||||
|
||||
To debug the usb capture
|
||||
```sh
|
||||
sudo apt-get install v4l-utils
|
||||
```
|
||||
To disable password while sudo
|
||||
Edit sudoer list by following command and add the below line bottom.
|
||||
```sh
|
||||
sudo visudo -f /etc/sudoers.d/90-username
|
||||
```
|
||||
username ALL=(ALL) NOPASSWD:ALL
|
||||
>replace username with armbian user name.
|
||||
|
||||
### To enable SPI UART and GPIO in rpi
|
||||
edit /boot/armbianEnv.txt
|
||||
```sh
|
||||
$ sudo nano /boot/armbianEnv.txt
|
||||
```
|
||||
>overlays=usbhost2 usbhost3 w1-gpio uart1 i2c0 spi-spidev
|
||||
>param_w1_pin=PA20
|
||||
>param_w1_pin_int_pullup=1
|
||||
>param_uart1_rtscts=1
|
||||
>param_spidev_spi_bus=1
|
||||
|
||||
example file may look like after editing:
|
||||
>verbosity=1
|
||||
>console=both
|
||||
>overlay_prefix=sun50i-h5
|
||||
>overlays=usbhost2 usbhost3 w1-gpio uart1 i2c0 spi-spidev
|
||||
>rootdev=UUID=abc1d3dd-6193-4fb7-93fb-f50382b8a8b9
|
||||
>rootfstype=ext4
|
||||
>param_w1_pin=PA20
|
||||
>param_w1_pin_int_pullup=1
|
||||
>param_uart1_rtscts=1
|
||||
>param_spidev_spi_bus=0
|
||||
>usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u
|
||||
|
||||
Note
|
||||
>If you are using pin 19 and 23 for SPI for rpi pins then spi is /dev/spidev1.0
|
||||
|
||||
Thats it, rpi is ready for Hyperion
|
Loading…
Reference in New Issue